πŸ“Š Mass Transfer
Q. Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number.
  • (A) Schmidt
  • (B) Sherwood
  • (C) Peclet
  • (D) Stanton
πŸ’¬ Discuss
βœ… Correct Answer: (A) Schmidt
πŸ“Š Mass Transfer
Q. If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is
  • (A) L/G
  • (B) G/L
  • (C) Always < 1
  • (D) None of these
πŸ’¬ Discuss
βœ… Correct Answer: (A) L/G
πŸ“Š Mass Transfer
Q. For achieving rapid drying rate in a spray dryer, the diameter of the particles in the feed should be in the range of __________ microns (1 mm = 1000 microns).
  • (A) 1-5
  • (B) 10-60
  • (C) 200-300
  • (D) > 500
πŸ’¬ Discuss
βœ… Correct Answer: (B) 10-60
πŸ“Š Mass Transfer
Q. Berl saddle made of carbon cannot be used for
  • (A) Alkalis
  • (B) SO2
  • (C) H2SO4
  • (D) Oxidising atmosphere
πŸ’¬ Discuss
βœ… Correct Answer: (D) Oxidising atmosphere
πŸ“Š Mass Transfer
Q. Capacity of a rotary dryer depends on its
  • (A) rpm
  • (B) Inclination with ground surface
  • (C) Both (A) and (B)
  • (D) Neither (A) nor (B)
πŸ’¬ Discuss
βœ… Correct Answer: (C) Both (A) and (B)
πŸ“Š Mass Transfer
Q. The most common packing used in industrial operations is __________ rings.
  • (A) Raschig
  • (B) Lessing
  • (C) Cross-partition
  • (D) Single spiral
πŸ’¬ Discuss
βœ… Correct Answer: (A) Raschig
πŸ“Š Mass Transfer
Q. Refractory bricks are usually dried in a __________ dryer.
  • (A) Tray
  • (B) Tunnel
  • (C) Conveyor
  • (D) Festoon
πŸ’¬ Discuss
βœ… Correct Answer: (B) Tunnel
πŸ“Š Mass Transfer
Q. Occurrence of 'case hardening' during drying of a high moisture solid cake __________ the drying rate.
  • (A) Increases
  • (B) Decreases
  • (C) Does not affect
  • (D) Exponentially increases
πŸ’¬ Discuss
βœ… Correct Answer: (B) Decreases
πŸ“Š Mass Transfer
Q. The binary diffusivity in gases at atmospheric conditions is about
  • (A) 10-9 cm/sec
  • (B) 10-1 cm2/sec
  • (C) 10-3 sec/cm
  • (D) 10-4 cm2/sec2
πŸ’¬ Discuss
βœ… Correct Answer: (B) 10-1 cm2/sec
πŸ“Š Mass Transfer
Q. For absorbers, high pressure drop results in
  • (A) Increased efficiency
  • (B) Decreased efficiency
  • (C) High operating cost
  • (D) Better gas liquid contact
πŸ’¬ Discuss
βœ… Correct Answer: (C) High operating cost

Jump to